Integrated Circuit

Product Details:

It consists of six positive-edge triggered D-type flip-flops the true outputs from each flip-flop are externally available. The CD40175B consists of four positive edge triggered D-type flip-flops both the true and complement outputs from each flip-flop are externally available. All flip-flops are controlled by a common clock and a common clear information at the D inputs meeting the set-up time requirements .

Additional Information:

• Delivery Time: 2-15DAYS

Product Details:

The LM386 and LM386MX-1 are power amplifiers designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value from 20 to 200.

Product Details:

Number of Bits8Sampling Rate (Per Second)10kNumber of Inputs1Input TypeDifferentialData InterfaceParallelConfigurationADCRatio - S/H:ADC-Number of A/D Converters1ArchitectureSARReference TypeExternal, SupplyVoltage - Supply, Analog4.5V ~ 6.3VVoltage - Supply, Digital4.5V ~ 6.3VFeatures-Operating Tem KADIO 19 KADIO 200 KADIO

Additional Information:

• Delivery Time: 2-15 DAYS

Product Details:

Operates from ±5-V to ±18-V SuppliesLess than 10-µs Acquisition TimeLogic Input Compatible With TTL, PMOS, CMOS0.5-mV Typical Hold Step at Ch = 0.01 µFLow Input Offset0.002% Gain AccuracyLow Output Noise in Hold ModeInput Characteristics Do Not Change During Hold Mode

Product Details:

The LM565 and LM565C are general purpose phase locked loops containing a stable, highly linear voltage controlled os- cillator for low distortion FM demodulation, and a double bal- anced phase detector with good carrier suppression.

Product Details:

UC3845 is a high-performance fixed-frequency current-mode controller designed for offline and DC-to-DC converter applications, providing designers with a cost-effective solution that requires minimal external components.

Product Details:

A High Performance Current Mode Controllers T he UC3842A, UC3843A series of high perf ormance fixed frequency current mode co ntrollers are specifically designed for off−line and DC−to−DC converter applications offering the designer a co st effective solution with minimal exte rnal components.

Product Details:

Logic IC Type ENCODERSub Category Arithmetic CircuitsFamily 74147JESD-30 Code R-PDIP-T16Load Capacitance (CL) 15.0  pFNumber of Bits 9Number of Functions 1Number of Terminals 16Operating Temperature-Min 0.0  CelOperating Temperature-Max 70.0  CelOutput Polarity INVERTEDPackage Body Material PLASTIC/EPOXYPackage Code DIPPackage Equivalence Code DIP16,.3

Product Details:

Length: 19.3 mm ; Logic Type: Priority Encoder ; Low Level Output Current: 8 mA ; Maximum Clock Frequency: 35 MHz.Function: EncoderSupply Voltage - Max: 5.25 VLength: 19.3 mmNumber of Input Lines: 8 Input

Product Details:

SN74LS123 Retriggerable Mono stable Multivibrators These dc triggere d multivibrators feature pulse width co ntrol by three methods.The basic pulse width is programmed by selection of ex ternal resistance and capacitance value s.

Product Details:

74LS112A dual JK flip-flop features individual J, K, clock, and a synchronous set and clear inputs to eac h flip-flop.When the clock goes HIGH, the inputs are enabled and data will be accepted.

Product Details:

74LS107A is a Dual JK Flip -Flop with individual J, K, Direct Clea r and Clock Pulse inputs.Output change s are initiated by the HIGH-to-LOW tran sition of the clock.A LOW signal on CD input overrides the other inputs and m akes the Q output LOW

Product Details:

The LM567 and LM567C are general purpose tone decoders designed to provide a saturated transistor switch to ground when an input signal is present within the passband. The circuit consists of an I and Q detector driven by a voltage controlled oscillator which determines the center frequency of the decoder.

Product Details:

The SG3525AN is a regulating pulse width Modulator IC is designed to offer improved performance and lowered external parts count when used in designing all types of switching power supplies. The on-chip 5.1V reference is trimmed to ±1% and the input common-mode range of the error amplifier includes the reference voltage eliminating external resistors. A single resistor between the CT and the discharge terminals provide a wide range of dead time adjustment. This device also features built-in soft-start circuitry with only an external timing capacitor required.

Product Details:

IC,Semiconductors,Diodes,Mosfets,IGBTs,Capacitors,tantalums,Sensors -All full Range available-Cost Rs.1 to Rs.2000

Additional Information:

• Production Capacity: As per requirement
• Delivery Time: Ready stock
• Packaging Details: Standard

Product Details:

15-V Digital or ±7.5-V Peak-to-Peak Switching• 125-Ω Typical On-State Resistance for15-V Operation• Switch On-State Resistance Matched to Within5 Ω Over 15-V Signal-Input Range• On-State Resistance Flat Over FullPeak-to-Peak Signal Range• High On or Off Output-Voltage Ratio:80 dB Typical at fis = 10 kHz, RL = 1 kΩ• High Degree of Linearity: <0.5% Distortion Typicalat fis = 1 kHz, Vis = 5-Vp-pVDD – VSS ≥ 10-V, RL = 10 kΩ• Extremely Low Off-State Switch Leakage,Resulting in Very Low Offset Current and HighEffective Off-State Resistance: 10 pA Typical atVDD – VSS = 10-V, TA = 25°C

Additional Information:

• Delivery Time: 2-15DAYS

Product Details:

The CD4027B types are supplied in 16-l ead hermetic dual-in-line ceramic packa ges (F3A suffix), 16-lead dual-in-line plastic packages (E suffix), 16-lead sm all-outline packages (M, M96, MT, and N SR suffixes), and 16-lead thin shrink s mall-outline packages

Additional Information:

• Delivery Time: 2-5 DAYS

Product Details:

The ICL8038 waveform generator is a monolithic integratedcircuit capable of producing high accuracy sine, square,triangular, sawtooth and pulse waveforms with a minimum ofexternal components. The frequency (or repetition rate) canbe selected externally from 0.001Hz to more than 300kHzusing either resistors or capacitors, and frequencymodulation and sweeping can be accomplished with anexternal voltage

Product Details:

The L298 is an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals

Product Details:

The LM353 is a JFET input operational amplifier with an internallycompensated input offset voltage. The JFET input device provideswith bandwidth, low input bias currents and offset currents8 DIPFEATURES• Internally trimmed offset voltage: 10mV • Low input blas current: 50pA8 SOP• Wide gain bandwidth: 4MHz High slew rate: 13VusHigh Input impedance: 10

Product Details:

The TL494 device incorporates all the functions required in the construction of a pulse-width- modulation (PWM) control circuit on a single chip. Designed primarily for power-supply control, this device offers the flexibility to tailor the power-supply control circuitry to a specific application

Product Details:

ITs a monostable multivibrator featuring both positive and negative edge triggering with complementary outputs. An internal 2kΩ timing resistor is provided for design convenience minimizing component count and lay- out problems. this device can be used with a single exter- nal capacitor.

Product Details:

DUAL 1-OF-4 DECODER/ DEMULTIPLEXER The L STTL/MSI SN54/74LS139 is a high speed D ual 1-of-4 Decoder /Demultiplexer. The device has two independent decoders, ea ch accepting two inputs and providing f our mutually exclusive active LOW Outpu ts.

Product Details:

SN74LS14 Schmitt Triggers Dual Gate/Hex Inverter The SN74LS14 contains logic g ates / inverters which accept standard TTL input signals and provide standard TTL output levels.They are capable of transforming slowly changing input sign als into sharply defined, jitter-free o utput signals.

Product Details:

The MAX232 device is a dual driver/receiver that includes a capacitive voltage generator to supply TIA/EIA-232-F voltage levels from a single 5-V supply. Each receiver converts TIA/EIA-232-F inputs to 5-V TTL/CMOS levels.

Product Details:

SN74LS32 Quad 2−Input OR Gate VCC 14 13 12 11 10 9 8 1234567 GND GUARAN TEED OPERATING RANGES Symbol Paramete r Min Typ Max Unit VCC Supply Voltage TA Operating Ambient Temperature Range 4.

Product Details:

MUR860 is a high-voltage, ultra-fast recovery rectifier diode designed for high-frequency switching applications. It is commonly used in SMPS, inverters, free-wheeling, and snubber circuits, where fast switching and low reverse recovery time are critical.

PKG : TO-220-2L
VBR (V) Min : 600 V
VBR (V) TYP : 640 V

Product Details:

The L298N is a high-power dual full-bridge motor driver IC designed to control DC motors, stepper motors, and inductive loads in industrial and robotics applications. It is capable of driving higher current motors compared to L293D, making it suitable for medium-to-high power motor control

Make : XBLW
PKG : ZIP-15 Dual Full-Bridge Driver
Operating Voltage(v) : 4.5-46V
Quiescent Current Iq(Typ) : 10mA
Drive Current Iout : 4A

Product Details:

The NE555N is the most common version of the legendary 555 timer IC, housed in a DIP-8 (Dual In-line Package) through-hole format. The "N" suffix specifically denotes the plastic package style meant for breadboards and traditional PCB mounting

Product Details:

L7905CT is a fixed negative voltage regulator manufactured by STMicroelectronics. It is part of the L79xx series, which includes a range of three-terminal negative regulators 

Product Details:

FULL RANGE OF WXDH MOSFETS FOR UPS, INVERTORS, POWERSUPPLIES, LED LIGHTING , EV 2 WHEELERS & EV 4 WHEELERS MOSFETS AVAILABLE

Product Details:

Low Power Monostable Ast able Multivibrator General Description CD4047B is capable of operating in eith er the monostable or astable mode It re quires an external capacitor (between p ins 1 and 3) and an external resistor ( between pins 2 and 3) to determine the output pulse width in the monostable mo de and the output frequency in the asta ble mode Astable operation is enabled b y a high level on the astable input or low level on the astable input The outp ut frequency (at 50% duty cycle) at Q a nd Q outputs i .

Additional Information:

• Delivery Time: 2-5 DAYS

Product Details:

Type of Control Channel: N -Channel
Maximum Power Dissipation (Pd): 200 W
Maximum Drain-Source Voltage |Vds|: 60 V
Maximum Gate-Source Voltage |Vgs|: 20 V
Maximum Drain Current |Id|: 70 A
Maximum Junction Temperature (Tj): 150 °C
Rise Time (tr): 79 nS
Drain-Source Capacitance (Cd): 530 pF
Maximum Drain-Source On-State Resistance (Rds): 0.012 Ohm

Product Details:

TRIMMED OSCILLATOR DISCHARGE CURRENT ■ CURRENT MODE OPERATION TO 500kHz A UTOMATIC FEED FORWARD COMPENSATION DIP -8 SO-8 ■ LATCHING PWM FOR CYCLE-BY -CYCLE CURRENT LIMITING

Product Details:

Logic IC Type BINARY COUNTERSub Category CountersCount Direction UPFamily LSJESD-30 Code R-PDIP-T16Load/Preset Input YESMax Frequency@Nom-Sup 2.5E7  HzMax I(ol) 0.008  AmpMode of Operation SYNCHRONOUSNumber of Bits 4Number of Functions 1Number of Terminals 16Operating Temperature-Min 0.0  CelOperating Temperature-Max 70.0  CelPackage Body Material PLASTIC/EPOXYPackage Code DIPPackage Equivalence Code DIP16,.3

Product Details:

SN74121N IC, 74TTL, 74121, DIP14, 5V Logic Case Style: DIP MSL: - Multivibrator Type: Monostable No. of Pins: 14 Operating Temperature Max: 70°C Operating Temperature Min: 0°C Output Current: 16mA Packaging: Each Propagation Delay: 45ns SVHC: No SVHC (15-Jun-2015) Supply Voltage Max: 5.25V Supply Voltage Min: 4.75V

Product Details:

Principle among these is square wave signal conditioning and cleanup, as the 74HC14 functions as a comparator and the built-in hysteresis provides noise immunity on the input terminals. This makes it a good candidate for accepting low-level signals in industrial applications or other areas where signals may be noisy

Product Details:

SN74LS153 Dual 4-Input Multiplexer The L STTL / MSI SN74LS153 is a very high spe ed Dual 4-Input Multiplexer with common select inputs and individual enable in puts for each section.It can select tw o bits of data from four sources.The t wo buffered outputs present data in the true (non-inverted) form.In addition to multiplexer operation, the LS153 can generate any two functions of three va riables.The LS153 is fabricated with t he Schottky barrier diode process for h igh speed

Additional Information:

• Delivery Time: 2-5DAYS

Product Details:

TL074 Low-noise JFET quad operational a mplifier D SO14 (plastic micropackage) Output 1 1 Inverting Input 1 2 - N on-inverting Input 1 3 + VCC + 4 Non -inverting Input 2 5 + Inverting Input 2 6 - Output 2 7 14 Output 4 - 13 Inverting Input 4 + 12 Non-inverting Input 4 11 VCC - + 10 Non-inverting I nput 3 - 9 Inverting Input 3 8 Outpu t 3 Pin connections (top view) Datash eet - production data Related products

Product Details:

The NE555N is a highly popular precision timer integrated circuit used for generating accurate time delays, oscillation, and pulse generation. Known for its simplicity, reliability, and versatility, it is widely used in both educational and industrial electronic applications.

Specifications:

• Make : HLF
• PKG : DIP-8 Single Chip
• Control Circuit: Operating voltage 4.5- 16V,
• maximum output current 1.5A,
• voltage accuracy +2%,
• adjustable output voltage ADJ,
• switching frequency 100KHz.